Changing the LED lights inside your favored controller is rather basic. For each controller you will require a reduced wattage soldering iron, 60/40 rosin, a sponge, a pair of pointed tweezers, and your brand-new LEDs. You can use a greater power level iron, but it is safer to start with a reduced watt so you prevent potentially destroying your motherboard. To open a 360 controller, you will need a t8 screwdriver. A small Phillips head screwdriver is utilized for the ps3. When taking the screws from the 360 controller there is an unseen screw discovered inside the battery pack terminal behind the oblong shaped bar code sticker label.
To start you will need to tin the soldering iron. This just means to melt rosin on the iron then cleanse it off with your sponge. When cleaning the iron, I discovered it works most effectively to obtain the sponge somewhat wet on one side. I such as to cleanse the iron after each action to raise contact.
When you have the screws secured there are a few actions you will wish to avoid breaking your controller case. To disassemble the xbox 360 controller, you will have to push in the thumbsticks and gently tear the controller apart. To prevent losing any of your buttons, I advise applying a strip of tape to the front of the controller to hold everything in place. After you have actually done this, you will should pull the rubber thumb sticks off their system, extract the motherboard, and set every little thing aside so you do not lose anything.
The PS3 controller is rather easier to dismantle. When you have the screws eliminated, you will simply pull the two halves apart. Next, you will pull the rubber joysticks off, and pull the tab that connects the R's and L's off their clip. You are now ready to remove the old lights from the motherboard.
To eliminate the LEDs, I like to utilize a method called drifting. To do this, you will have to melt some rosin on the iron till it makes a little bit of bubble on the iron itself. It might appear like it is going to fall off, but do not fret, it will remain on the iron. As soon as you have this done, you will drift the bubble back and forth across the LED to eliminate it. This will most likely take simply a couple of seconds and the LED will stick to the rosin. Then you will simply cleanse the iron off and duplicate the process for each light.
Applying the brand-new LEDs is a little more difficult than taking them off. Initially, you will have to look at the bottom of the new LED and determine which side the arrow on the bottom is pointing. You will need to point the arrow to the negative side of the motherboard. If you can not figure this out, turn the power to the controller on and the LED will light up if you have correctly lined it up. I such as to leave the battery pack and the back half of the controller connected. This is so I could make use of the contact pad to turn the controller on. For the ps3, you could simply plug in the charging cable. When you have straightened them correctly, you will use your tweezers to hold the LED in place and simply add a little bit of rosin to both side and you are done. It may take some time however a little practice will make things a great deal easier. Now you are ready to show off your newly light controller with your most loved color lights!
To start you will need to tin the soldering iron. This just means to melt rosin on the iron then cleanse it off with your sponge. When cleaning the iron, I discovered it works most effectively to obtain the sponge somewhat wet on one side. I such as to cleanse the iron after each action to raise contact.
When you have the screws secured there are a few actions you will wish to avoid breaking your controller case. To disassemble the xbox 360 controller, you will have to push in the thumbsticks and gently tear the controller apart. To prevent losing any of your buttons, I advise applying a strip of tape to the front of the controller to hold everything in place. After you have actually done this, you will should pull the rubber thumb sticks off their system, extract the motherboard, and set every little thing aside so you do not lose anything.
The PS3 controller is rather easier to dismantle. When you have the screws eliminated, you will simply pull the two halves apart. Next, you will pull the rubber joysticks off, and pull the tab that connects the R's and L's off their clip. You are now ready to remove the old lights from the motherboard.
To eliminate the LEDs, I like to utilize a method called drifting. To do this, you will have to melt some rosin on the iron till it makes a little bit of bubble on the iron itself. It might appear like it is going to fall off, but do not fret, it will remain on the iron. As soon as you have this done, you will drift the bubble back and forth across the LED to eliminate it. This will most likely take simply a couple of seconds and the LED will stick to the rosin. Then you will simply cleanse the iron off and duplicate the process for each light.
Applying the brand-new LEDs is a little more difficult than taking them off. Initially, you will have to look at the bottom of the new LED and determine which side the arrow on the bottom is pointing. You will need to point the arrow to the negative side of the motherboard. If you can not figure this out, turn the power to the controller on and the LED will light up if you have correctly lined it up. I such as to leave the battery pack and the back half of the controller connected. This is so I could make use of the contact pad to turn the controller on. For the ps3, you could simply plug in the charging cable. When you have straightened them correctly, you will use your tweezers to hold the LED in place and simply add a little bit of rosin to both side and you are done. It may take some time however a little practice will make things a great deal easier. Now you are ready to show off your newly light controller with your most loved color lights!
